How to build a closet in corner of room

No matter if you live in a large home or a small apartment, closet space is a need, so it is necessary to know how to build a closet in corner of room. Over time, the available closet space became too little to accommodate a large increase in apparel. So, inventiveness is essential, especially for those of you who live in small apartments or dorm rooms because you can have very little or no closet space.

How to build a closet in corner of room

Several corners in your room are unoccupied and may be used as closet space if you take a look around. To know how to build a closet in corner of room. You should know that you can use a room corner that is currently empty as additional storage space.

There are so many wonderful ideas. Do you know how to build a DIY closet without spending a lot of money or time? Just eliminate the layouts that don’t fit into the vacant spaces in your home or room. We already have a few fantastic DIY corner closet ideas. See which one you prefer?

A corner closet is frequently the best choice if you need additional closet storage and are prepared to give up some floor space to acquire it. All that is required is the building of one or two walls, dry walling, and door installation.

While an angular design only requires one wall, a square or rectangle closet requires two. An angular closet’s drawback is that, although taking up less space overall than a square-cornered design, it produces much less closet space, especially for hanging garments.

A simple 2 x 4 frame may be used to construct the corner closet’s walls because they are not load-bearing. Steel studs are an option as well, although wood framing is preferable to steel for securing shelving and fasteners. Purchase the door for your closet before you start construction, so you’ll know precisely how big to make the rough door opening.

See more: Maximize Your Space: Discover Closet System with Drawers

How do you plan a closet layout?

To know how to build a closet in corner of room, you have to determine how much closet space you require.

The first place to look is your existing closet to determine what you need to store there. Before beginning the design of a closet procedure, it is advisable to do a little cleaning.

For each person whose clothing will be housed in the new closet, figure out the following details using your present closet.

Half of the hanging area is wide overall. Clothing items like shirts, knee-length skirts, and pants that are hung folded in the middle need a half-hanging area.

The breadth of the entire hanging area. For garments such as gowns and long coats, a full hanging area is necessary.

How much shelf space is folded objects occupying? What are the dimensions of your folded items? Depending on the folded object, you might wish to divide this group. A huge sweater takes up more space on a shelf than a t-shirt, therefore it makes it logical to place those in different categories.

How much drawer space do you use? Again, breaking things down into individual items, such as nightwear, underwear, socks and hosiery, exercise equipment, belts, scarves, etc., might be useful.

Specify the sizes of your purses.

What else are you going to need to have in your closet? Make a note of any extra room needed for shoes, caps, or other accessories.

How much space do I need around a corner of closet?

Think about if a dressing table will be in your bedroom or walk-in closet.

In a corner, a basic rule of thumb is to allow 12′′ of blank wall space between closet pieces. Since shelving is 12″ deep, the distance to a closet portion is 24″. Clothing hanging in the corner may now be accessed completely.

How much does it cost to build a simple closet?

How to build a closet in corner of room? Building a reach-in custom closet often has the lowest cost, ranging from $500 to $1,500. Typically, built-in wardrobes cost between $1,000 and $2,500. Nevertheless, if you need to do repairs to make a sufficient area, building a built-in closet might cost substantially more.

A bespoke freestanding wardrobe normally costs between $1,000 and $3,000 to have built by a contractor. If you don’t already have a place to install a reach-in or built-in type, a standalone wardrobe is frequently more economical. Contractors can incorporate elements like rails and shelves to create a bespoke closet’s convenience without the pricey upgrades.

Frequently, wall-mount designs are less expensive than floor-mount designs.

See more: Wooden closet organizer ideas

TOOLS & MATERIALS

In the context of talking about how to build a closet in corner of room. The cost of your project as a whole might be considerably impacted by the materials you use. Depending on the hue, laminate can range in price from $135 to $235 (CDN 185 to CAD 325) per linear foot. But, you may have to spend up to $330 (CDN 455) per linear foot if you choose an uncommon color or expensive material.

What you’ll require

Resources / Tools

  • Powerful miter saw
  • Stud detector
  • Plaster tape
  • Measurement tape
  • Laser level and plumbing tool
  • Bar pry
  • Hammer
  • Tools for finishing drywall
  • Painting supplies

Materials

  • 2 24-inch by 80-inch bifold doors
  • 3 3/4-inch by 4 1/2-inch by 81-inch (true width) primed interior door jamb molding
  • 2 48-inch door trim kits
  • 4 Drywall sheets
  • 10 Two-by-fours
  • 16d nails
  • Toggle bolts
  • Drywall paper tape
  • Drywall compound
  • Drywall primer
  • Interior paint

How to Build a Closet From Scratch

How to Build a Closet From Scratch

How to build a closet in corner of room? The key is careful preparation. It’s been said that you should cut once after measuring twice in carpentry. It also holds while considering how to construct a closet. Check and measure everything.

Don’t forget to account for the thickness of the drywall and timber. To plan out the closet’s depth, width, and door placement, temporarily stick painter’s tape to the walls, floor, and ceiling.

It is simpler to pick the closet doors in advance so that the frame may be constructed to fit. Whenever possible, picking the internal storage system in advance is also a smart idea.

Mark out the closet, and fit the wall plates

Take out the carpet, tile, or flooring that is currently in the closet space. The bottom should be marked first, followed by the sides, and then the top. Be very careful. As work goes on, any mistakes here are likely to get worse. Verify each layout line and measurement twice.

Cut the 2*4s for the top and bottom wall plates—the horizontal load-bearing framing—to length using a miter saw or handsaw.

A full-length floor plate, which is a board that rests flat on the floor and supports the framework, might not be necessary if the closet is being constructed into a little corner. Doors typically need to remove portions of the bottom plate from lengthier closets. It is better to do this once the main construction has been put together and is stiff.

Attach the bottom plate to the floor using screws. Mark the location of the doors and fasten them with screws on either side, but not through the plate’s portion that will need to be removed to make room for the door opening.

If at all feasible, fasten the top plate to the ceiling joists; locate them using a stud finder. If it is not possible to do this, hollow wall anchors must be utilized.

A solid connection cannot be established simply by screwing into drywall. To distribute the weight throughout the surface and provide the required holding force, hollow drywall anchors (toggles) open up underneath the drywall.

Frame the walls and headers

For the end walls, cut studs that are full height, and either screw or use drywall anchors to fasten them to joists. Screw two 2*4s together with discarded blocks sandwiched between them to provide a larger stud for corner pieces or center dividers. Toe-screw is to insert a nail into the floor and top plates at an approximately 45-degree angle from both sides, close to the ends. When necessary, install extra studs to support drywall or door frames. Just 16 inches should separate the studs.

To place trimmers onto the upright studs, measure the height needed for the doors. They are the horizontal lengths of wood above the doors that serve as headers, and they will support the ends of those. To sit properly, the door headers were cut, and they were screwed in.

Now, it is possible to cut support components known as “cripples” or “cripple studs” to fit between the top plate and door header. Toe-screw them into position and space them 16 inches apart.

After the construction is solid, cut through the bottom plates where the doors will fit using a handsaw, then take out that material.

Install drywall, corner bead if necessary, and then tape and fill

To know how to build a closet in corner of room, you need to install drywall, corner bead if necessary, and then tape and fill.

It’s time to apply the drywall once the frame has been installed. If cutouts are required, cutting drywall with a handsaw is a common practice. Nevertheless, experts employ the following technique for straight lines since it is faster and more precise: Using a utility knife, carve a line through the backside that extends deep enough to cut into the core. Cut through the front paper after snapping the board. To continue making clean cuts, constantly replace the utility knife’s blades.

Using the screws approximately 12 inches apart and slightly below the surface, fasten the drywall to the studs.

If there is a closet divider, start with it before moving on to the exterior. If the closet doesn’t completely occupy the wall, the outer corner will need to be strengthened with a corner bead before being completed, taped, and finished.

Fit the doors and trim

Standard, bifold, and sliding are the three different styles of closet doors. We advise picking the ones you want at the planning stage because each requires distinct considerations when fitting.

About how to build a closet in corner of room, the simplest doors to fit are sliding ones. Most just need runners at the top, where the doors hang. They don’t fit well in tiny closets, since they still occupy a lot of room when they are open. A common substitute that frequently follows a similar logic is bifold doors. Most have thorough instructions.

It might be difficult to put hinges on standard single or door pairs. Prehung doors are simpler since suitable sizes might be hard to locate. The only thing left to do is to secure the door frame to the aperture because the hinges are already in place. Thin shims are used for adjustments, which are subsequently covered by trim installed around the door frame.

Finish with rods, shelves, and storage accessories

How to build a closet in corner of room? Individuals with the necessary DIY abilities might choose to make their closet organizers fit within the closet, but a variety of storage items, such as this well-rated Rubbermaid Set from Amazon., are inexpensive and adaptable.

The same guidelines that apply to fitting studs also apply to mounting shelves or closet rods. The studs that are already there behind the drywall may be screwed into if you know where they are. If you don’t, you should utilize hollow drywall anchors.

The storage system may be carrying a significant amount of weight if jackets, shoes, and other goods have been added. The entire thing might pull away if it isn’t firmly fastened to the wall.

See more: L shaped closet system: Why is it important?

FAQ | How to build a closet in corner of room?

Can a closet be placed in a corner?

A corner closet is frequently the best choice if you need additional closet storage and are ready to give up some floor space to obtain it.

What is the ideal corner closet solution?

Only one hanging portion should extend into a closet corner to get the most out of the space.

Get In Touch


Articles